An analytical method for the determination of Al, Ca, Cd, Cr, Cu, Fe, Hg, K, Mg, Na and Zn in breast of conventional, country and Christmas chicken and turkey samples using microwave induced plasma optical emission spectrometry (MIP-OES) technique was developed. Samples were decomposed in a digester block with a reflux system under conditions optimized using a central composite design as it follows: 2 g of sample, in 7.5 mL of HNO3 during 180 min at 160 °C. The accuracy was evaluated by the analysis of standard reference material SRM 1546 meat homogenate (94 to 108%) and also by addition and recovery tests (80 to 121%). The highest concentrations, in mg kg-1, of Al (2.77), Ca (88.3), Cu (1.99), Fe (3.65), K (3236), Mg (292.62) and Na (312.03) were found in the breast of conventional chicken sample. Zinc presented high value in the breast of turkey sample (10.6 mg kg-1). However, the found concentrations were lower than the daily consumption limit established by supervisory agencies and reference limits from Brazilian legislation. Cadmium, Cr and Hg presented values below limit of quantification. In this way, it is evident that chicken breast should be consumed in a complementary way in a healthy diet.

The objective of this study was to evaluate the concentration of Cu, Zn, Cr and Pb in different species of fish collected in the estuarine and limnic regions of the São Gonçalo channel, located in the Patos-Mirim lagoon complex in the coastal plain of Rio Grande do Sul State (Southern Brazil) during 2013 (autumn, winter and spring) and 2014 (summer). Fish samples were decomposed in a digester block with a reflux system under conditions optimized using a central composite design as it follows: 250 mg of fish sample, 5 mL HNO3, 2 mL H2O2 during 2 h at 150 °C. The concentrations obtained ranged from 6.7 to 12.0 mg kg -1 for Cu; 1.8 to 23.6 mg kg -1 for Zn; 37 to 487 µg kg -1 for Pb; and 40 to 1268 µg kg -1 for Cr. The highest concentrations of Cu, Zn and Pb, were observed in fishes collected at locations in the estuarine region and Cr showed high levels, especially in the limnic region. The samples of the species Loricariichthys anus (viola) showed the highest concentrations of all analytes investigated.

This paper presents a study involving the development of a new mini polytetrafluoroethylene (PTFE) vessel project for biological sample preparation in micro scale in closed system with microwave radiation for subsequent determination of Cd, K, Mg and Na by atomic spectrometry techniques. All experiments were carried out in micro quantities of samples (up to 20 mg) and reagents (300 µL of HNO3) for 5 min at 350 W. Certified reference materials of biological samples (bovine muscle and liver) were used to evaluate the accuracy of the proposed system and the results obtained were in agreement with the certified value at 95% of confidence (t -test). Relative standard deviations (RSD) were lower than 8.0% for all elements. The proposed method is not only easy and fast, but it is also based on the use of an inexpensive system for sample digestion.

In this work, the photochemical vapor generation (PVG) coupled with atomic absorption spectrometry and a pre-concentration step with an Au column was used for the determination of Hg in biological samples and ethanol fuel. PVG with pre-concentration showed an up to 250-fold higher sensitivity compared to the approach without pre-concentration. The accuracy of analysis of biological samples was evaluated using certified reference materials (fish tissues), while for ethanol fuel samples, recovery tests were employed (91%). Analytical curves were linear (R > 0.99) in the studied range of 2.5 to 10 µg L-1 for conventional PVG and 0.2 to 0.5 µg L-1 for PVG with the pre-concentration step. For the last, the limits of detection reached for biological samples and ethanol fuel were 0.02 and 0.01 µg L-1, respectively. The systems presented are simple, sensitive and safe for the control of low Hg concentrations in different samples. However, only the system using pre-concentration with an Au column was capable of obtaining the reproduced signals of Hg in low concentrations of the order of 0.2 µg L-1.

This paper describes the optimization of a sample preparation method using response surface methodology for Al, Cd, Cu, Fe, Mg, Mn, Mo, Na, Ni and Ti determinations in samples of rice husk and rice husk ash by MIP OES. Sample preparation was performed using a reflux system adapted to the digestion tubes. This system allowed the decomposition of the samples without the necessity of replacement of the acids during this step without any loss of volatile elements. The decompositions were performed with 3.6 mL of HNO3 and 1.4 mL of H2SO4 for 205 min in a digester block at 225 ºC. The detection limit for determination of respective analytes in both samples were satisfactory. The RSDs for the analytes were less than 10%. Moreover, the accuracy of the method can be verified by recovery tests, whose values ranged from 82 to 115% for husk samples and 82 to 120% for ashes. The proposed method was presented as a simple, safe and low cost procedure being suitable for sample preparation and subsequent determination of metals by MIP OES.

In this work, two sample preparation procedures for subsequent determination of Na, K, Ca and Mg by techniques of atomic spectrometry in samples of Brazilian cream cheese were evaluated. The determinations were performed on two equipments, F AAS and MIP OES, which presented similar results, being evident the advantages of MIP OES since it is a multielementar technique with low operational cost and high efficiency. The first procedure was carried out by acidic decomposition (HNO3/H2SO4) in a reflux system, and the second used the alkaline solubilization with tetramethylammonium hydroxide. The accuracy was verified by recovery tests and the results were between 80 and 104% for both procedures. A comparison with a reference procedure was also performed and no significant differences have been observed at the 95% confidence level. The evaluated elements were not in accordance with the values indicated on the labels of all products, showing the importance for monitoring these products. The methods of sample preparation proposed showed to be simple, inexpensive, providing accurate and precise results, and are a promising alternative to be used for the quality control of these routine test samples.

This paper describes the method optimization using response surface methodology for Cu, Fe, Zn and Na determinations in coal and ash samples by spectrometry techniques. The sample preparation was performed using a recirculation system adapted in the digestion tubes. This system allowed increase of temperature in the digester block above the boiling point of the reaction medium, avoiding acid evaporation during the heating. The digestions were realized with HNO3 and H2O2 for 1 h in a digester block at 145 °C. The limits of detection for determination of Cu, Fe, Zn and Na in both samples were satisfactory. The RSD for the analytes were lower than 6.0%. Statistical tests showed that results for all analytes do not vary significantly with official method (ASTM), considering a confidence limit of 95%. Besides, the accuracy was verified by recovery tests, whose values ranged from 92.7 to 104.7% in coal, and 98.7 to 115.3% in ash.

The aim of this study was to evaluate the performance of a reflux system adapted in the digestion tubes in sample preparation of xanthan gum for subsequent determination of Ca, Cu, K, Mg, Na and Zn by using spectrometric techniques. Through the proposed method, the samples were digested with HNO3 for 3 h in a digester block at 220 °C. The accuracy of the method was evaluated by comparing the results with another sample preparation method and by using recovery tests, which results vary between 83 and 103%. The efficiency of digestion was assessed and significant results were verified through residual carbon values, which were five times lower compared to conventional acid digestion in open system, with use of HNO3 and HClO4. The proposed methodology is a simple and accurate analytical strategy, which does not require the use of special equipment, neither a mixture of strong oxidizing acid in the sample preparation.

In the first part of this paper, two acid decomposition procedures for the determination of Al, Ca, Fe, Mg, Mn and Zn contents in yerba mate samples by inductively coupled plasma optical emission spectrometry (ICP OES) were compared. Using a reflux system, the samples were treated with a mixture of HNO3 and H2O2 for 3 hours at 220 °C in the digester block. The results from five commercial yerba mate samples were compared with the results obtained from microwave digestion. Good agreement between the procedures at a 95% confidence level was obtained with relative standard deviation (RSD) values lower than 10.0%. The accuracy was evaluated using addition and recovery experiments (80.5 to 112.8%). In the second part, Ca, Cd, Cr, Cu, Fe, K, Mg, Na, Pb and Zn concentrations were evaluated in the yerba mate infusion. The results showed that elements such as Na, K, Mg and Zn are easily transferred to the hot water used for the infusion. For Pb and Cd, the concentrations found in the analyzed samples were lower than the values established by Brazilian legislation.

This paper describes the evaluation of a method for determination of Cd and Pb in xanthan gum samples by Graphite Furnace Atomic Absorption Spectrometry (GF AAS) using NH4H2PO4 as the chemical modifier. The sample preparation was performed using a reflux system adapted in the digestion tubes. With this system it was possible to increase the temperature of the digester block above the boiling point of the reaction medium, preventing loss of analyte and excessive evaporation of acids during heating. Samples were digested with HNO3 for 3 h in a digester block at 220 ºC. The limits of detection for Cd and Pb were 2.2 and 33.8 ng g-1, respectively. The RSDs for both analytes were, on average, lower than 5.0% and accuracy was verified by recovery tests, yielding values in the 83-100% range.

This paper describes the evaluation of simple and fast solubilization methods for the determination of Ca, Mg, and K in glycerin samples from biodiesel production by atomic spectrometry. The solubilization in water was compared with two other methods: solubilization in formic acid and solubilization in ethanol. Using solubilization in water, determination of the three analytes was possible; the values of limits of detection for Ca, K, Mg were 0.31, 0.06, and 0.16 mg kg−1, respectively. Because no adequate reference material was available, the accuracy was evaluated by assessing the recoveries tests with both solubilization methods; the evaluation ranged from 90% to 115%, with values of relative standard deviation >8%, indicating good accuracy of the measure. Four crude glycerin samples obtained from biodiesel plants of Rio Grande do Sul were analyzed after treatment with the different methods of solubilization, and the obtained results of Ca, Mg, and K concentration were in agreement with the values obtained from both solubilization methods. Therefore, solubilization in water is concluded to be a simpler, faster, and viable method for sample preparation of glycerin.

Apresenta-se um procedimento alternativo para o preparo das amostras de biodiesel para a determinação elementar por espectrometria de emissão óptica com plasma indutivamente acoplado (ICP OES), baseado na formação de emulsão da amostra (10% m/v) com ácido fórmico (15% v/v) e Triton X-100 (0,1% m/v). Estas concentrações foram otimizadas e os padrões e amostras emulsionados mostraram-se estáveis por pelo menos 3 h. As condições experimentais (1500 W de potência da radiofrequência e 0,5 L min-1 de vazão do Ar nebulizador) foram otimizadas a partir das recomendadas pelo fabricante do equipamento, com uma solução contendo 10 mg L-1 de todos os analitos, preparada com óleo base nas mesmas condições da emulsão. Os efeitos de matriz foram investigados, observando as inclinações das curvas de adição de analito para diferentes amostras de biodiesel. Os resultados mostraram que a calibração externa com soluções contendo padrões inorgânicos emulsionados pode ser utilizada. Os limites de detecção encontrados (em mg kg-1) foram 0,121; 0,008; 0,006; 0,001; 0,006; 0,071; 0,241 e 0,024 para Ca, Cu, Fe, Mn, Mg, Na, K e Si, respectivamente. A exatidão do procedimento para o Ca, Mg, K e Na foi avaliada por meio da análise de um padrão multielementar de biodiesel B100 (Conostan) e as recuperações variaram entre 91 a 107%. O procedimento proposto usa reagentes com baixa toxicidade e mostrou ser uma alternativa simples e direta de preparação de amostras para determinação de metais em biodiesel por ICP OES com limites de detecção adequados para essas análises.

It is presented an alternative procedure for preparation of biodiesel samples for elemental determination by inductively coupled plasma optical emission spectrometry (ICP OES), based on the sample (10% m/v) emulsion formation with formic acid (15% v/v) and Triton X-100 (0.1% m/v). These concentrations were optimized and the stability of emulsified aqueous standards and samples was found to be of at least 3 h. Experimental conditions (1500 W of RF power and 0.5 L min-1 of Ar nebulizer flow rate) were optimized from those recommended by the equipment manufacturer, with a solution containing 10 mg L-1 of each analyte prepared with mineral oil in the same conditions of the emulsion. Matrix effects were investigated by observing the slopes of analyte addition curves for different biodiesel samples. Results showed that external calibration with inorganic aqueous standard solutions in the emulsion medium should be used. Limits of detection obtained (in mg kg-1) were 0.121, 0.008, 0.006, 0.001, 0.006, 0.071, 0.241 and 0.024 for Ca, Cu, Fe, Mn, Mg, Na, K and Si, respectively. The accuracy of the procedure for Ca, Mg, K and Na was assessed by the analysis of a multi-element standards B100 biodiesel (Conostan) and the recoveries ranged from 91 to 107%. The proposed procedure used low toxicity reagents and showed to be a simple and straightforward alternative of sample preparation for metal determination in biodiesel by ICP OES with limits of detection adequate for those analyses.

Foram avaliados dois métodos diferentes de preparo de amostras de carnes baseados na solubilização em meios alcalino ou ácido. O objetivo deste estudo foi determinar os teores de Na e K após solubilização com hidróxido de tetrametilamônio (TMAH) temperatura ambiente, e com ácido fórmico e aquecimento em bloco de digestão a 50 ºC por cerca de 2 h. A solubilização alcalina se apresentou como uma metodologia simples e robusta e a melhor alternativa frente aos procedimentos de mineralização convencional, permitindo a solubilização completa das amostras usando pequenas quantidades de TMAH. O método foi validado empregando-se materiais de referência certificada assim como pela comparação com método de digestão convencional com ácido nítrico. Os limites de detecção obtidos foram de 0,8 e 2,0 mg g-1 para Na e K, respectivamente, e se mostraram adequados para o objetivo das análises.

Two different sample preparation methods were evaluated for meat samples employing the solubilization in alkaline or acidic media. The aim of this study was to determine Na and K levels after sample solubilization with tetramethylammonium hydroxide (TMAH) at room temperature, and with formic acid and heating in a digester block at 50 ºC for ca. 2 h. The alkaline solubilization showed to be a simple and robust method and the better alternative in relation to the mineralization conventional procedures, allowing the complete solubilization of the samples even when small quantities of TMAH were used. The method was validated by using certified reference material as well as by comparing with samples digested with nitric acid. The limits of detection obtained were 0.8 and 2.0 μg g-1 for Na and K, respectively, and showed to be adequate for the analysis purposes.

Recentemente, a Associação Brasileira de Normas Técnicas (ABNT) lançou uma série de normas, relacionadas com a determinação de Na, K, Mg e Ca em biodiesel, recomendando procedimentos similares àqueles das normas europeias e americanas, mas também introduzindo uma norma alternativa (ABNT NBR 15556), que possibilita a determinação dos 4 elementos usando a técnica de espectrometria de absorção atômica com chama (F AAS). Neste trabalho, apresentam-se os estudos de otimização e validação que dão suporte a essa norma, bem como a comparação do desempenho de um equipamento com fonte de linhas com outro de fonte contínua. Entre os fatores otimizados, os baixos valores de taxa de aspiração e o uso de uma solução de óleo mineral em xileno para o ajuste da viscosidade entre soluções das amostras e de calibração devem ser destacados. Testes de precisão (repetitividade e precisão intermediária) mostraram valores adequados, comprovando a robustez do método, e os limites de detecção estiveram confortavelmente abaixo daqueles propugnados pelas legislações brasileira e internacional. A exatidão foi confirmada por testes de recuperação e pela participação em exercícios interlaboratoriais de proficiência promovidos pela Agência Nacional de Petróleo, Gás Natural e Biocombustíveis (ANP). A determinação dos 4 elementos por F AAS traz evidentes vantagens econômicas ao produtor, uma vez que se trata de um equipamento mais barato na sua aquisição e manutenção.

Recently, ABNT (Brazilian Association of Technical Standards) has presented a set of norms related to the determination of Na, K, Mg and Ca in biodiesel, recommending procedures similar to those of the European and American norms. However, it has also introduced an alternative norm (ABNT NBR 15556) wherein these 4 elements can be determined by flame atomic absorption spectrometry (F AAS). This work presents the studies that have supported this proposal and compares the performance of linear source equipment with a continuous source one in the application of the norm. Among the optimized factors, the low aspiration rate and the use of mineral oil solution in xylene to adjust the viscosity between samples and calibration solutions are highlighted. Precision tests (repeatability and intermediary precision) have shown adequate values, confirming the robustness of the method. Limits of detection were suitably below the legislation limits. The accuracy was confirmed by recovery tests as well as by the participation in interlaboratory proficiency tests promoted by the National Agency on Oil, Natural Gas and Biofuels (ANP, Brazil). The determination of these 4 elements by F AAS brings evident economic advantages to the producer, once F AAS is less expensive to purchase and maintenance.

Um método simples para o tratamento de amostras de carne fresca e processada com hidróxido de tetrametilamônio (TMAH) é proposto para a determinação de Ca, Fe e Mg por espectrometria de absorção atômica com chama (FAAS) e Cu por espectrometria de absorção atômica com forno de grafite (GFAAS). A exatidão foi avaliada por comparação dos resultados usando outros dois procedimentos de preparo de amostra e por análise de materiais de referência certificados. Não houve diferença significativa entre os resultados obtidos, em um nível de confiança de 95%. Os limites de detecção para Ca, Cu, Fe e Mg foram 45,0, 0,2, 16,0 e 0,3 µg g-1, respectivamente. A espectrometria de absorção atômica de alta resolução com fonte contínua em forno de grafite (HR-CS GFAAS) foi empregada para avaliar as interferências espectrais na determinação de Cu. Entretanto, nenhuma interferência foi encontrada. O método proposto é simples, rápido e confiável para análise de produtos cárneos e não requer o uso de equipamentos especiais nem de ácidos fortes no preparo das amostras.

A simple method for treating fresh and processed meat with tetramethylammonium hydroxide (TMAH) is proposed for the determination of Ca, Fe and Mg by flame atomic absorption spectrometry (FAAS) and Cu by graphite furnace atomic absorption spectrometry (GFAAS). The accuracy was evaluated by comparison of the results by using two other sample preparation procedures and by the analysis of certified reference materials. No significant differences between the results were found at the 95% confidence level. Limits of detection for Ca, Cu, Fe and Mg were 45.0, 0.2, 16.0 and 0.3 µg g-1, respectively. High-resolution continuum source graphite furnace atomic absorption spectrometry (HR-CS GFAAS) was employed to evaluate the spectral interference in the determination of Cu. However, no interference was found. The proposed method is simple, fast and reliable for meat products analysis and does not require especial equipment, neither strong acid for sample preparation.